DC 12V 24V Dual MOS LED Digital Time Delay Relay Trigger Cycle Timer Delay Switch Circuit Board Timing Control Module DIY

Solid State RelaysProduct description:0.1 seconds (min) to 999 minutes (max) continuouslyadjustable.This product is easy to use, many functions, but allbuyers need to carefully read the instructions, veryuseful product.Product Features:1,To achieve fast turn-on and off the circuit, anunlimited number of switching;2,Conducting and cutting process does not producenoise, no spark, no electromagnetic interference,3,Compared with electromagnetic relay productslonger life;4,The dual-MOS parallel drive, lower resistance.more current, strong power; at room temperature,operating current of up to 15A, power up to 400W to meet the most use of the equipment;5,A method for controlling the motor, lights, LED, DCmotors, micro-pumps, solenoid valves, etc., veryconvenient.Pay attention:1,Wide voltage input (5 ~ 36V), most devices can beused, very convenient;2,The interface is clear and simple, powerful, easyto understand, meet almost all your needs;3,The emergency stop function ("STOP" key);Withreverse polarity protection, reverse polarity wilnot burn the product.4,Increase the sleep mode, if this mode is enabled,without any within 5 minutes, thenautomatically turn off the monitor, any keywake-up;5,You can set a different OP, CL, LOP parameters,which are independent of each other, and areautomatically saved;6,After the module is powered down, all parametersettings are not lost.Product Parameters:1: Operating voltage: 5-36V2:Trigger Source: Active-high (3.0V-24V), haveoptocoupler isolation, can improve the system'santi-jamming capability(customers can also shortingcommon ground).3: Output capacity: DC 5V- 36V, at room temperature,continuous current 15A, power 400W! Enhance heatdissipation conditions, the maximum current up to 30A.4: Quiescent Current: 20mA; Operating Current: 50mA5: Life: any switching times; Working temperature:-40-85°;Size:6.0*3.4*1.2cm.6: With optocoupler isolation, enhanced anti-jammingcapability, industrial grade board.Pay attention:1.The module is an active output, the output voltageequal to the input voltage.2.'DC + 'and' load + 'This is an internal short circuitof the poles, but' DC-'and' load- 'poles during usecan not be shorted, otherwise the load can not becontrolled on and off, which is equivalent load isbeen carrying electricity.Operating mode:P1: trigger signal, the relay is on "OP" time, and thendisconnect; in the "P" time, as follows:P1.1: signal is triggered again, invalidP1.2: signal is triggered again, the clock is resetP1.3: Signal trigger again, relay off, stop the clock;P-2: trigger signal, the relay off "CL" of time, the relayon "OP" time, and then disconnect relay;P3.1: trigger signal, the relay is turned on after the"OP" time, the relay off "CL" time, then the operationcycle, if the trigger signal period, the relay off, stopthe clock; the number of cycles ("LOP ") can be setP3.2: without triggering signal, the relay is on "OP"time, the relay off "CL" time, and has been cycling;frequency ("LOP") cycle can be set;P-4: signal holding function. lf there is a trigger signaltiming is cleared, the relay remains on; when the signaldisappears, after the timing "OP" time, the relay is; ifanother signal during timing, timing is cleared;Timing range:0.1 seconds (min) to 999 minutes (max) continuouslyadjustableHow to choose the time range?After setting the mode selection screen parametervalue by a short press "STOp" button to select thetime range;. decimal point in the unit place, time range:1 second to 999 seconds.X decimal point in decade place, Timing range: 0.1seconds to 99.9 secondsX.X. decimal full brightness, Timing range: 1 minuteto 999 minutes.For example, you want to set "OP" is 3.2 seconds,then move the decimal point to decade place, thedigital display 03.2Parameter description: "OP" - conduction time, "CL"off time, "LOP" - the number of cycles (1-999 times,"---" represents infinite loop)These parameters are independent of each otherbut is shared by each mode. For example, in P1.1 mode,set the on-time "OP" is 5 seconds, if you switch to P1.2 mode, it's "OP" will be 5 seconds too.In the main interface (display 000), short press"SET" button will display "OP" ( "CL", "LOP") and the corresponding time ;Some parameters only mode "OP" (such as the modeP1.1, P1.2, P1.3), short press the "SET" key to displayonly the "OP" and the corresponding time;Some models have parameters "P", "CL", "LOP" (suchas the mode P3.1, P3.2), short press "SET" button willdisplay "OP" and the corresponding time, "CL" and thecorresponding time, "LOP" and the correspondingnumber of times;In the main interface by short press "SET" key to seeinformation about the parameters of the current mode.very convenient!How to set parameters?1,First, read the instructions to determine the requiredoperating mode.2,The module is powered up, the display at the currentwork mode (P1.1 default mode), then enter the maininterface; press "SET" button for 2 seconds after releaseto enter mode selection interface; a short time bypressing "UP", "DOWN" key to select the mode(P1.1~P-4)3,Select the mode (such as P3.2),short press the'SET" button, then the parameter to be set flashes("P" on-time, "CL" off time, "LOP" cycles("---" represents infinite loop)), by "UP","DOWN"keys to adjust the parameter value, support long press(rapid increase or decrease) and short press (increaseor decrease unit); then short press the "STOP" keyto select the decimal point position, select the timerange (0.1 seconds to 999 minutes); short press the"SET" button to set the next parameters of the currentmode of procedure is as above.4,After the parameters are set, long press "SET"button for 2 seconds then release, the name of thecurrent mode will flash once, and then return to themain screen, set the parameters of success!The main interface: In the relay does not work statusdisplay "000" (no decimal point), with a decimal pointunder relay state.Mode selection screen: Long press the "SET" key toenter, after setting is completed, long press the "SET'key to exit back to the main screen."STOP" button extensions:Relays enable mode:ON: Relay allows conduction in the "OP" on-time;,OFF: relay prohibit conduction is always closed;In the main interface, short press the "STOP" button toswitch between ON and OFF, the current in which thestate will flash, and then return to the main screen.(This feature is an emergency stop function, click offthe relay)Sleep mode:"C-P" Sleep mode: five minutes without anyoperation, the digital display automatically turns off,the program running as usual;"0-d" normal mode: digital display always open;Press the "STOP" button for two seconds and thenrelease to switch "C-P" and "O-d" state, in which thecurrent state of flashes and then return to the mainscreen.Package Included:1 x Trigger Cycle Timer Delay Switch 12V 24V CircuitBoard MOS Tube Control Module==========Theory : Time RelayContact Load : Low PowerModel Number : DC 12V 24V Dual MOS LED Digital Time Delay Relay Trigger Cycle Timer DVoltage : 5VUse : Purpose

• Solid State Relays
• Theory : Time Relay
• Contact Load : Low Power
• Model Number : DC 12V 24V Dual MOS LED Digital Time Delay Relay Trigger Cycle Timer D
• Voltage : 5V
• Use : Purpose